The Art of Basic Plumbing When You Install a Bathtub
The Art of Basic Plumbing When You Install a Bathtub
Blog Article
Every person will have their own unique assumption when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bathtub isn't precisely brain surgery, however it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is easily obtainable, the project can relocate quickly; if you have to open a wall to remove the old bathtub and also place the new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and embeded in the brand-new one. Ensure you have actually qualified yourself for the task and are comfortable attempting it. Instead of working with a specialist to take control of a halfway-completed job, it is better to think about utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will certainly aid you mount a brand-new tub in your washroom if you have actually already acquired a new bathtub and do not need to change the plan of your previous water system pipes.
Your tools and also material checklist must make up the following:
Getting ready for the Setup
To start with, the sustaining frame provided with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any kind of water remaining in the system. The process of eliminating the existing taps can be fairly bothersome as a result of the limited accessibility that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, position the bath tub in the called for placement. The wooden boards are useful in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the bath tub up until the spirit level reads level.
To set up taps, fit the bottom of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; then do the very same for the other tap.
Turn on the water system as well as check all joints and also new pipework for leaks as well as tighten them if essential. Fill the bathtub as well as also inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, repair the bath paneling as explained in the producer's user's manual. Tiling as well as securing around the tub must wait until the bathtub has been used at least once as this will settle it right into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Secure the faucet in position with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet ports. The former type needs to be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, causing the water to permeate the wall surface between the bath and also the tiling, causing difficulties with dampness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are offered in tubes and cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealant can crack relatively early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is suggested to fit the floor tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader on A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece of content was a smart idea. In case you enjoyed reading our article plz remember to pass it around. Thank you so much for going through it.
Act now! Report this page